The name axon comes from Latin and is translated as line or wave. Both apply equally to this loudspeaker: the close arrangement of the 12 x 3" wideband loudspeakers in a vertical line achieves particularly good coupling, thus creating a flat wavefront over a wide frequency range.

Conventional loudspeakers have 6 db sound pressure loss per doubling of distance. The axon becomes only 3 dB more silent. The advantage is a more even sound distribution on the listening area: close to the speaker not too loud and far away still clear and intelligible.

The column is curved at the bottom for good coverage at close range. The rear wall of the housing has remained straight, so that the Axon can also be mounted flat on the wall or on poles using a non-visible bracket. Together with the slim construction, this results in a very elegant and discreet design. The Axon is therefore predestined for fixed installations and mobile use, where excellent sound and a sophisticated visual appearance are important.

The angled Speakon connector panel can be exchanged for a connector plate with Phoenix contact plug connector or waterproof PG cable gland.

For flight or tripod operation and mounting in installations, various thread points, swivel brackets as well as wall and mast brackets are available. A Safety-Point allows a Single-Studs with safety rope to be clicked into place for the prescribed secondary protection.


  • At any suitable amplifier with integrated DSP or upstream DSP Controller. Filter values are freely available for individual settings. Limiter values can be adjusted by yourself.
  • Plug&Play on the TENNAX self-powered Subwoofern (Combi-Sets).
  • Plug&Play on Powersoft amplifiers with ready-to-use presets for Armonia Plus software.
  • About the TENNAX (AllDSP) 19“ DSP-Controller with any suitable amplifier. Filter values are already set, limiter values can be adjusted by yourself (Limiter preset to 32 dB amp gain).

Technical Data

12 x 3" Wideband transducer

Frequency range
100 Hz - 16 kHz (- 10 dB)
140 Hz - 14 kHz (+/- 3 dB)

Coverage range (h x v)
80° x 20°

12 Ω

Powerhandling (AES / program / peak)
240 W / 480 W / 960 W

Sensitivity 1 W/1 m
95,5 dB SPL

Sound pressure at (AES / program / peak)
119 dB SPL / 122 dB SPL / 125 dB SPL

2 x Neutrik NL4 IN/OUT 1+/- (4-pole looped-through)

Polyurea coating in RAL 9005

Dimensions / Weight
1.034,5 (H) × 115 (W) × 145 mm (D) / 7,4 kg



Carrying bag for Axon-12x3 or X-Tension Kit


Carrying bag for 1 x Axon-12x3 with or without mounted bracket and tripod mount or 1 x X-Tension Kit. Strong Codura fabric with padding.

X-Tension Kit for Axon-12x3


The 91.5 cm high X-Tension Kit is inserted between the subwoofer and Axon-12x3 to raise the column to a visually appealing height. Speaker cables can be elegantly routed through it. The mechanics allow a quick and uncomplicated assembly. The X-Tension Kit can be mounted on any subwoofer or steel base plate with an M20 thread. The Axon-12x3 carrying bag can be used to transport the X-Tension Kit.

Tripod transducer


Tripod transducer with threaded pin M10 x 12 mm and large clamping screw for locking to the tripod. For all common speaker stands with Ø 35 mm.

U-bracket for U bracket for Axon-12x3


Stable swivel bracket for installation on trusses and ceiling. 2 x M10 hexagon head screws included in delivery.

C-bracket für Axon-12x3


Stable swivel bracket for vertical mounting on walls. The bracket is attached at the top and bottom of the M10 mounting points. Thanks to the oblong holes in the bracket, the Axon-12x3 can be fixed as close as possible to the wall after the swivels. 2 x M10 hexagon head screws included in delivery.

Flat knurled screw M10 x 25 mm


Flat knurled screw M10 x 25 mm, steel black burnished for all u- and c-brackets. As an alternative to the hexagonal bolts supplied with the brackets.

Hand lever M10 x 30 mm


Hand lever M10 x 30 mm, adjustable, flat design, steel black burnished with plastic lever, suitable for all U- and C-brackets.

Clamp holder for Axon-12x3


Two clamp holders for mounting on the rear wall of the Axon-12x3. With this, the Axon-12x3 can be attached to columns and masts, for example, using various types of clamps. For clamp width up to 38 mm.

Wall holder for hidden mounting Axon-12x3


There is also an elegantly concealed mounting option without the bracket. The back cover plate of the loudspeaker is recessed into the box, giving a cavity behind which space is available for a wall mount. The loudspeakers can be mounted on a small wall mount corner plate and secured with an inauspicious grub screw.

Self-lock clamp


Loudspeakers can be flown by one person with the self-lock clamp. The clamp hooks directly into the truss and can be easily tightened. Load capacity 250 kg.

Truss clamp


With this traverse clamp you can easily and loosely mount your devices to all common traverses with 48-51 mm strap tubes. The clamp impresses with its compact design, its lightness and the maximum tensile load of 100 kg. Locking screw M8 Wing nut and device screw M10.

Eye Bolt M10 x 40 mm


M10 x 40 mm eyebolt, for M10 mounting points. Load capacity 250 kg.

Single stud


Single stud for securing a loudspeaker with safety cable.

Safety 6/1000


1 m safety cable 6 mm Ø for securing a suspended loudspeaker. One side with a screwable quick connect.

Inclinable Stand Adapter


With this adapter you can attach speakers without built-in flange on stands or wall brackets and adjustable up to 30 ° in the tilt. Max. load capacity: 15 kg.

Tilting and swivelling wall holder


Wall holder with large wall plate for heavy boxes. The mounted box can be swivelled sideways and tilted up to 30 °. Easy installation due to practical mounting and screwing. Max. load capacity: 25 kg.

Wall mount with extension


Wall mount with extension (180° horizontal and 30° vertical adjustment) for parallel positioning. Max. Load capacity: 25 kg.

Wall holder can be swiveled and tilted


Wall holder with tilt and swivel orientation: 145° horizontal, 30° vertical. The inclination can be fixed in 6 steps. The distance to the wall can be selected in 3 steps. With receptacle for high stand flange. Holder is almost completely covered by the speaker. Max. Load capacity: 25 kg.

Wall holder flange big


Stable wall holder with tilt and swivel orientation: 180° horizontal, 22° vertical adjustable in 11 steps. Expanding mandrel for play-free seating in the tripod base of the speaker. Max. load capacity: 50 kg.

Wall- and Trussholder


Wall- and Trussholder with a joint and a tube clamp, circa 520 mm long. Max. load capacity: 50 kg.

Speaker ceiling mount


Robust ceiling mount with 250 mm distance and internal cable management. The swivel area is +/-45 °. Within the parameters - the settings range from 0 to 45°. Max. load capacity: 25 kg.

Multifunctional rotating ceiling bracket


For hanging speakers from ceilings using steel cables or chains and various accessories. Horizontal alignment due to central pivot axis. Max. load: 60 kg. Available in white and black. Supplied without further mounting accessories.

Telescopic rod


Telescopic rod with expanding mandrel system for play-free seating in the tripod base. Height: 110 to 180 cm. Max. load capacity: 35 kg.

Distance rod with crank


Distance rod for cranking with expanding mandrel system which provides a tight and firm fit for the speaker. Height: 92 - 152 cm. Max. load capacity: 50 kg.

Speaker stand crank


Stable stand for cranking with double protection against falling. Height: 139 to 218 cm. Max. load capacity: 50 kg.

Speaker stand


Stable stand with expanding mandrel system which provides a tight and firm fit for the speaker. Double protection against falling. Height: 132 - 220 cm. Max. load capacity: 50 kg.

Carrying bag for 2 x speaker stand/ rod


Carrying bag for two speaker stands or distance rods, also with crank. Two inside compartments with zipper and sturdy handles. Material waterproof nylon.

Cable Clip for speaker stand/ rod


The cable clip made of robust, durable ABS plastic is specially designed for speaker stands and distance rods with 35 - 36 mm tube. It adheres firmly to the tube and holds the cables securely and neatly in the 24 x 16 mm guide accessible from the outside.

Iron base with weight plate


The set includes a flat 10 kg iron base Ø 45 and a 5 kg weight disc. It is suitable distance rods with an M20 screw thread. The weight disc can be mounted tool-free.

Carrying bag for round base Ø 45 cm


Padded bag made of robust, water-repellent nylon, with space for a round base Ø 45 cm with weight disc. The bag has two carrying straps with a soft velcro handle, a sturdy zipper and a transparent window for labels.

speakON cable 0.5/1/3/6/10/15/20/30 m


Speaker cables in various lengths with Neutrik plug NL4FX. 4 x 4 sq mm, each wire 224 x 0.15 copper, diameter 11 mm, weight 273 g / m. Assembled with some pressed ferrules for maximum contact area and minimal contact resistance.

speakON adapter


Adapter to connect two speaker cables.

Connection plate with waterproof PG thread cable gland


The angled Speakon connector panel can be exchanged e.g. for installation purposes outdoors against a connector plate with waterproof PG thread cable gland.

Connection plate with Phoenix-contact connector strip


The angled Speakon connector panel can be exchanged e.g. for installation purposes for a connection plate with Phoenix contact plug connector.

Phoenix Contact


Phoenix Contact 4 pol. as an alternative to the Neutrik NL4 Speakon IN/OUT.